{"id":4566,"date":"2023-07-31T16:32:00","date_gmt":"2023-07-31T08:32:00","guid":{"rendered":"https:\/\/www.qhsmt.com\/?p=4566"},"modified":"2023-08-02T09:43:04","modified_gmt":"2023-08-02T01:43:04","slug":"pick-and-place-machine-pcb-testing-methods-guide","status":"publish","type":"post","link":"https:\/\/www.qhsmt.com\/zh\/2023\/07\/31\/pick-and-place-machine-pcb-testing-methods-guide\/","title":{"rendered":"PCB Testing Methods Guide sharing"},"content":{"rendered":"

Before explaining the inspection work after the PCB wiring is completed, I will introduce three special wiring techniques for PCB. The routing of PCB LAYOUT will be explained from three aspects: right-angle routing, differential routing, and serpentine routing.Today author from QiHe smt pick and place machine discussing about it with you .<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Right-angle routing (three aspects)<\/h3>\n\n\n\n

The impact of the right-angle trace on the signal is mainly reflected in three aspects: first, the corner can be equivalent to a capacitive load on the transmission line, slowing down the rise time; second, the impedance discontinuity will cause signal reflection; third, the EMI generated by the right-angle tip. In the field of RF design above 10GHz, these small right angles may become the focus of high-speed problems.<\/p>\n\n\n\n

Differential routing (“equal length, equidistant, reference plane”)<\/h3>\n\n\n\n

What is a differential signal? In layman’s terms, the driver sends two equal and inverted signals, and the receiver judges the logic state “0” or “1” by comparing the difference between the two voltages. The pair of traces that carry differential signals is called a differential trace. Compared with ordinary single-ended signal routing, differential signals have the most obvious advantages in the following three aspects:<\/p>\n\n\n\n

1) Strong anti-interference ability, because the coupling between the two differential traces is very good, when there is noise interference from the outside world, they are coupled to the two lines almost at the same time, and the receiving end only cares about the difference between the two signals, so the external common mode noise can be completely offset.<\/p>\n\n\n\n

2) It can effectively suppress EMI. For the same reason, because the polarities of the two signals are opposite, the electromagnetic fields radiated by them can cancel each other out. The tighter the coupling, the less electromagnetic energy is released to the outside world.<\/p>\n\n\n\n

3) Timing positioning is accurate, because the switching change of the differential signal is located at the intersection of the two signals, unlike ordinary single-ended signals that rely on high and low threshold voltages to judge, so it is less affected by the process and temperature, can reduce timing errors, and is more suitable for circuits with low-amplitude signals. The currently popular LVDS (low voltage differential signaling) refers to this small-amplitude differential signaling technology.<\/p>\n\n\n\n

Serpentine line (adjustment delay)<\/h3>\n\n\n\n

Serpentine lines are a type of wiring method often used in Layout. Its main purpose is to adjust the delay to meet the system timing design requirements. The two most critical parameters are the parallel coupling length (Lp) and the coupling distance (S). Obviously, when the signal is transmitted on the serpentine line, coupling will occur between the parallel segments, in the form of differential mode. The smaller the S, the larger the Lp, the greater the coupling degree. It may lead to a reduction in transmission delay and greatly reduce the quality of the signal due to crosstalk. The mechanism can refer to the analysis of common-mode and differential-mode crosstalk.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Here are some suggestions for pcb layout engineers when dealing with serpentine lines:<\/h3>\n\n\n\n

1) Try to increase the distance (S) of the parallel line segments, at least greater than 3H, where H refers to the distance from the signal trace to the reference plane. In layman’s terms, it means routing around a large bend. As long as S is large enough, mutual coupling effects can be almost completely avoided.<\/p>\n\n\n\n

2) Reduce the coupling length Lp. When the delay of twice Lp approaches or exceeds the signal rise time, the generated crosstalk will reach saturation.<\/p>\n\n\n\n

3) The signal transmission delay caused by the serpentine line of the strip line (Strip-Line) or the embedded microstrip line (Embedded Micro-strip) is smaller than that of the micro-strip line (Micro-strip). Theoretically, the stripline will not affect the transmission rate due to differential mode crosstalk.<\/p>\n\n\n\n

4) For signal lines with high speed and strict timing requirements, try not to take serpentine lines, especially in a small area.<\/p>\n\n\n\n

5) Serpentine wiring at any angle can be often used, which can effectively reduce mutual coupling.<\/p>\n\n\n\n

6) In high-speed PCB design, the serpentine line has no so-called filtering or anti-interference ability, which can only reduce the signal quality, so it is only used for timing matching and has no other purpose.<\/p>\n\n\n\n

7) Sometimes spiral routing can be considered for winding, and the simulation shows that its effect is better than that of normal serpentine routing.<\/p>\n\n\n\u9605\u8bfb\u66f4\u591a\uff1aPCB Testing Methods Guide sharing<\/span><\/a>\n\n\n

Best seller SMT Machine \uff1aQihe smt line products<\/h2>\n\n\n