{"id":5142,"date":"2023-11-24T16:44:00","date_gmt":"2023-11-24T08:44:00","guid":{"rendered":"https:\/\/www.qhsmt.com\/?p=5142"},"modified":"2023-11-07T10:05:35","modified_gmt":"2023-11-07T02:05:35","slug":"pick-and-place-machine-some-resistor-parameters-you-must-know-in-smt-process","status":"publish","type":"post","link":"https:\/\/www.qhsmt.com\/zh\/2023\/11\/24\/pick-and-place-machine-some-resistor-parameters-you-must-know-in-smt-process\/","title":{"rendered":"Some resistor parameters you must know in SMT process"},"content":{"rendered":"

The resistor is an ordinary component, but it has extraordinary ways. There are many parameters for resistors. We usually focus on resistance, accuracy, and power rating. These three indicators only need to be appropriate. It is true that in digital circuits, we do not need to pay attention to too many details. After all, there are only numbers 1 and 0, and we do not care about the minimal impact. But in analog circuits, when we use a precise voltage source, or perform analog-to-digital conversion of a signal, or amplify a weak signal, small changes in resistance will have a big impact. Today qihe smt pick and place machine sharing some resistor parameters you must know in SMT process .When we are fussing over resistors, of course we are dealing with analog signals. Later, we will analyze the impact of each resistor parameter based on analog circuit applications.<\/p>\n\n\n\n

Rated resistance of the resistor – The choice of the rated resistance of the resistor is often fixed by the application, such as limiting the current of an LED light, or sampling a certain current signal. There are basically no other choices for the resistance of the resistor. However, in some cases, there are many choices for resistors, such as amplifying a voltage signal. As shown in the figure, the amplification factor is related to the ratio of R2 and R3, and has nothing to do with the values of R2 and R3.<\/p>\n\n\n\n

At this time, there is still a basis for choosing the resistance of the resistor: the larger the resistance of the resistor, the greater the thermal noise, and the worse the performance of the amplifier; the smaller the resistance of the resistor, the greater the working current, and the greater the current noise. The performance of the amplifier will be worse; this is the reason why the resistance of many amplifier circuits is tens of K. Where large resistance values are needed, either a voltage follower or a T-type network is used to avoid this.<\/p>\n\n\n\n

\"Today<\/figure>\n\n\n\n

The accuracy of the resistor<\/h4>\n\n\n\n

the accuracy of the resistor is easy to understand, so I won\u2019t go into details here. The accuracy of resistors is generally 1% and 5%, and the precision is 0.1%, etc. The price of 0.1% is about ten times that of 1%, and the price of 1% is about 1.3 times that of 5%. Generally, the accuracy codes are A=0.05%, B=0.1%, C=0.25%, D=0.5%, F=1%, G=2%, J=5%, K=10%, M=20%.<\/p>\n\n\n\n

The rated power of the resistor<\/h4>\n\n\n\n

the power of the resistor is very simple, but it is often easy to use it inappropriately. For example, the rated power of a 2512 chip resistor is 1W. According to the resistor specification, when the temperature exceeds 70 degrees Celsius, the resistor must be derated. How much power can the 2512 chip resistor use? At normal temperature, if the PCB pad does not have special heat dissipation treatment, when the power of the 2512 chip resistor reaches 0.3W, the temperature may exceed 100 or even 120 degrees Celsius.<\/p>\n\n\n\n

At a temperature of 125 degrees Celsius, according to the temperature derating curve, the rated power of 2512 needs to be derated to 30%. This situation needs to be paid attention to in any packaged resistor. Do not be superstitious about the nominal power. It is best to confirm the key position again and again to avoid leaving hidden dangers.<\/p>\n\n\n\n

\"the<\/figure>\n\n\n\n

The withstand voltage value of the resistor<\/h4>\n\n\n\n

the withstand voltage value of the resistor is generally rarely mentioned, especially for novices, who often have no idea and think that only capacitors have the withstand voltage value. The voltage that can be applied to both ends of the resistor is determined by the rated power. It must be ensured that the power does not exceed the rated power. The other is the withstand voltage value of the resistor.<\/p>\n\n\n\n

Although the power of the resistor does not exceed the rated power, excessive voltage will cause instability of the resistor, creepage between resistor pins and other faults. When using it, a reasonable resistor must be selected according to the voltage used.<\/p>\n\n\n\n

The withstand voltage values of some packages include: 0603=50V, 0805=100V, 1206 to 2512=200V, 1\/4W plug-in=250V. Moreover, in time applications, the voltage on the resistor should be more than 20% smaller than the rated withstand voltage value, otherwise problems will easily occur over time.<\/p>\n\n\n\n

\"Today<\/figure>\n\n\n\n

Temperature Coefficient of Resistance<\/h4>\n\n\n\n

The temperature coefficient of resistance is a parameter that describes the change in resistance with temperature. This is mainly determined by the material of the resistor. Generally, packages of thick film chip resistors above 0603 can achieve 100ppm\/\u2103, which means that when the ambient temperature of the resistor changes by 25 degrees Celsius, the resistance value may change by 0.25%. If it is a 12-bit ADC, a change of 0.25% is 10 LSB.<\/p>\n\n\n\n

Therefore, op amps like the AD620 only rely on one resistor to adjust the amplification factor. Many experienced engineers will not use it for convenience. They will use a conventional circuit to adjust the amplification factor through the ratio of two resistors. When the resistors are of the same type When the resistance changes due to temperature, the ratio will not change, and the circuit will be more stable.<\/p>\n\n\n\n

For instruments that require higher precision, metal film resistors will be used. It is easy for them to achieve a temperature drift of 10 to 20 ppm, but of course they are more expensive. In short, in precision applications such as instruments, the temperature coefficient is definitely a very important parameter. If the resistance is not accurate, the parameters can be adjusted during calibration. The change of the resistance with the external temperature cannot be controlled.<\/p>\n\n\n\n

\"Today<\/figure>\n\n\n\n

Resistor structure<\/h4>\n\n\n\n

There are many resistor structures. Here are the applications that can be thought of. The starting resistor of the machine generally uses a resistor to precharge the large-capacity aluminum electrolyte. After the aluminum electrolyte is filled, the relay is closed and the power is turned on. <\/p>\n\n\n\n

This kind of resistor needs to be resistant to impact. It is best to use a large wire-wound resistor. The rated power of the resistor is not very important, but the instantaneous power is very high. It is difficult for ordinary resistors to meet the requirements.<\/p>\n\n\n\n

For high-voltage applications, such as capacitor discharge resistors, where the actual operating voltage exceeds 500V, it is best to use high-voltage glass glaze resistors instead of ordinary cement resistors.<\/p>\n\n\n\n

For peak absorption applications, for example, the two ends of the thyristor module need to be connected in parallel with RC for absorption and dv\/dt protection. It is best to implement a non-inductive wire-wound resistor, so that it can have good peak absorption performance and not be easily damaged by impact pick and place machine.<\/p>\n\n\n\u9605\u8bfb\u66f4\u591a\uff1aSome resistor parameters you must know in SMT process<\/span><\/a>\n\n\n

Best seller SMT Machine \uff1aQihe smt line products<\/h2>\n\n\n