{"id":7229,"date":"2026-11-18T20:39:42","date_gmt":"2026-11-18T12:39:42","guid":{"rendered":"https:\/\/www.qhsmt.com\/?p=7229"},"modified":"2026-11-18T20:39:54","modified_gmt":"2026-11-18T12:39:54","slug":"how-to-read-pick-and-place-machine-specs-cph-accuracy-repeatability","status":"publish","type":"post","link":"https:\/\/www.qhsmt.com\/zh\/2026\/11\/18\/how-to-read-pick-and-place-machine-specs-cph-accuracy-repeatability\/","title":{"rendered":"How to Read Pick and Place Machine Specs Correctly: CPH, Accuracy & Repeatability"},"content":{"rendered":"
How to Read Pick and Place Machine Specs Correctly: CPH, Accuracy & Repeatability<\/p>\n\n\n\n
When you shop for an SMT pick and place machine, you will quickly notice every supplier lists flashy pick and place machine specs: 80,000 CPH, \u00b10.02 mm accuracy, ultra-high speed. Many buyers take these parameters at face value, only to find the real output is far lower after installation.<\/p>\n\n\n\n
If you are running a small EMS workshop, prototype lab, or scaling up electronic assembly, understanding what these specs really mean will help you avoid overspending and select a machine matched to your BOM mix.<\/p>\n\n\n\n
CPH stands for Components Per Hour, the most widely used throughput indicator for chip mounters.<\/p>\n\n\n\n
It is critical to know: published CPH is almost always measured under ideal lab conditions<\/strong>. Manufacturers usually test with simple, uniform small passive components (0402 resistors and capacitors), optimized PCB layout, no feeder change, no program switch, and continuous feeding.<\/p>\n\n\n\n Real production CPH will drop significantly when:<\/p>\n\n\n\n For reference:<\/p>\n\n\n\n Do not chase the highest CPH blindly if your business is high-mix, small-batch electronics. Changeover time often kills your overall line efficiency more than raw placement speed.<\/p>\n\n\n\n This is the most common misunderstanding among SMT buyers.<\/p>\n\n\n\n A machine can have good repeatability but poor accuracy if it drifts after thermal expansion or loses calibration. For fine-pitch IC, QFP, BGA and 01005 components, repeatability is just as important as nominal accuracy.<\/p>\n\n\n\n General selection benchmark:<\/p>\n\n\n\n Vision system is the foundation of stable placement accuracy. Machines without on-board vision correction will struggle with slightly warped PCBs or tape component offset.<\/p>\n\n\n\n The speed and accuracy are useless if the machine cannot run your component packages. Check supported component range, nozzle types, electric feeder capacity and tray station options before purchase. Electric feeders deliver far lower pick-failure rates than pneumatic feeders for tiny chips.<\/p>\n\n\n\n Check maximum and minimum PCB dimension, board thickness and warpage tolerance. If you assemble long LED boards or thick power PCBs, this spec will become a hard limit.<\/p>\n\n\n\n Confirm it can read your centroid files from Altium, KiCad or other PCB design tools. Smooth program import reduces NPI setup time drastically.<\/p>\n\n\n\n \u2705 Ask suppliers whether the CPH number is theoretical or actual mixed-batch output \u2705 Confirm accuracy definition: single point placement or full IPC-9850 test standard \u2705 Ask about thermal compensation for long-run temperature drift \u2705 Check spare nozzle, feeder availability and overseas after-sales support \u2705 Match specs to your typical product mix instead of benchmarking the fastest model<\/p>\n\n\n\n Pick and place machine specifications are not just numbers on a datasheet. The best machine is not always the fastest one; it is the one that maintains stable yield, short changeover time and low downtime for your specific PCB products.<\/p>\n\n\n\n If you need a pick and place machine for high-mix low-volume SMT assembly, QiHe SMT provides flexible benchtop and full-automatic chip mounters with reliable vision systems and local overseas technical support.<\/p>\n\n\n\n Q: Is higher CPH always better? A: No. High CPH models are designed for simple mass production. For high-mix jobs, changeover time and feeder stability matter more.<\/p>\n\n\n\n Q: What accuracy do I need for 0201 components? A: We recommend \u00b10.02~\u00b10.03 mm placement accuracy with visual recognition.<\/p>\n\n\n\n Q: Can accuracy stay stable after long hours of running? A: It depends on motion control, thermal compensation and regular calibration. Our QM series adopts ARM+FPGA motion control to reduce thermal drift during continuous operation.<\/p>\n\n\n\n How to Read Pick and Place Machine Specs Correctly: CPH, Accuracy & Repeatability When you shop for an SMT pick and place machine, you will quickly notice every supplier lists flashy pick and place machine specs: 80,000 CPH, \u00b10.02 mm accuracy, ultra-high speed. Many buyers take these parameters at face value, only to find the […]<\/p>","protected":false},"author":1,"featured_media":7158,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_mi_skip_tracking":false,"footnotes":""},"categories":[731],"tags":[391,747,208,748],"class_list":["post-7229","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-pcb-assembly","tag-smt-mounter","tag-smt-pick-and-place-machine","tag-smt-production"],"aioseo_notices":[],"aioseo_head":"\n\t\t\n\t\n\t\n\t\n\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n
\n
2. Accuracy vs Repeatability: They Are Not the Same<\/h2>\n\n\n\n
\n
\n
3. Other Pick and Place Machine Specs You Should Not Ignore<\/h2>\n\n\n\n
Nozzle & Feeder Compatibility<\/h3>\n\n\n\n
PCB Size & Board Handling<\/h3>\n\n\n\n
Software & File Compatibility<\/h3>\n\n\n\n
4. Quick Checklist Before You Compare Quotations<\/h2>\n\n\n\n
Final Words<\/h2>\n\n\n\n
FAQ:<\/h2>\n\n\n\n
<\/a><\/figure>","protected":false},"excerpt":{"rendered":"